656faff4

Hyundai Getz>> Transmission>> Drive of forward wheels
Moments of an inhaling of carving connections, N · m
Nuts of fastening of wheels..... 90–100
Nut of a nave of a forward wheel..... 200–260
Nut of a bolt of fastening of a rack of a suspension bracket to a rotary fist..... 110–130
Nut of fastening of a spherical support of the lever of a suspension bracket to a rotary fist..... 60–72
Nut of fastening of the spherical hinge of a tip of steering draft..... 16–34
Bolts of fastening of the brake mechanism to a rotary fist..... 65–75
Nut of a nave of a back wheel..... 80–90
Bolt of the bottom fastening of the shock-absorber of a back suspension bracket..... 100–120

Technical characteristics
Parameter
Working volume
engine, l
1,1
1,3/1,5/1,6
Type of hinges of equal angular speeds:
1.наружный hinge
2.внутренний hinge

1. Type трипод with spherical crackers
2. Ball
Admissible angle of rotation of the hinge, hail, not less:
the external
the internal


45,3
22,3


45
22,5
Moment of resistance to a provorachivaniye of bearings of naves of wheels, N · m, no more:
lobbies
the back




1,8



0,99
1,8

Applied lubricants
Greasing place
Name
Quantity, g
Drive of forward wheels with ball and roller hinges (cars with the engine of 1,1 l and MKP):
    protective cover of ball hinges
    protective cover of roller hinges



СЕNTOPLЕХ 278M/136K



70±6
95±6
Drive of forward wheels with ball and roller hinges (cars with engines of 1,3/1,5/1,6 l and MKP or AKP):
    protective cover of ball hinges
    protective cover of roller hinges



СЕNTOPLЕХ 278M/136K



85±6
95±6

Removal and installation of drives of forward wheels
Design description

Fig. 3.81. Drive of a forward wheel: 1–lock ring; 2–shaft of a drive of a wheel; 3–lock ring; 4–nave bearing; 5–rotary fist; 6–protective casing; 7–brake disk; 8–a nut of fastening of a drive in a nave of a forward wheel


The drive and nave of a forward wheel are shown on rice 3.81 .
The drive of each wheel consists of two hinges of equal angular speeds and a shaft. The external hinge consists of the case, a separator, an internal holder and six balls. In the case of the hinge and in a holder flutes for placement of balls are executed. Flutes in the longitudinal plane are executed on radius that provides a demanded angle of rotation of the external hinge.
The Shlitsevy tip of the case of the hinge is established in a nave of a forward wheel and fastens to it a nut. The holder of the hinge is established on shlitsa of a shaft between a spring washer, a persistent ring and a lock ring.

       NOTE
For prevention of falling of a stripper 09568-34000 suspend it on a wire or a rope to any close located detail.

The internal hinge differs from external that paths of the case and a holder are executed by straight lines that allows details of the hinge to move in the longitudinal
the direction (it is necessary for compensation of the movings caused by fluctuations of a forward suspension bracket and the power unit), and also that an engine torque elements balls, and rollers are transferring not.
In the external hinge balls of one sorting group are established, all six balls of the hinge are if necessary replaced; balls should be one sorting group.
Details of hinges are greased with special greasing for hinges of equal angular speeds which is put in the case of hinges at assembly. Sealing of hinges is provided with rubber protective covers which fasten metal coupling collars.
Removal
Lift the car, remove a forward wheel.

Fig. 3.82. A nut of fastening of a drive in a nave of a forward wheel


Beat out шплинт and unscrew a nut of fastening of a nave of a forward wheel (fig. 3.82) .

Fig. 3.83. Vypressovka of a finger of the spherical hinge of a tip of steering draft from a rotary fist by means of a stripper 09568-34000


Vypressuyte a finger of the spherical hinge of a tip of steering draft from a rotary fist by means of a stripper 09568-34000 (fig. 3.83) .

Fig. 3.84. Fastening of a rack of a suspension bracket to a rotary fist


Disconnect a suspension bracket rack from a rotary fist (fig. 3.84) .
Merge oil from a transmission case.

Fig. 3.85. Knocking-out by a plastic kiyanka of a shaft of a drive of a wheel from a nave


Plastic kiyanka beat out a shaft of a drive of a wheel from a nave (fig. 3.85) .
Insert mount between a case of a transmission and the case of the internal hinge of a shaft of a drive of a wheel and, operating with mount as the lever, separate a shaft from a transmission.
Separate a wheel nave from a drive shaft, having moved a nave on itself.

PREVENTION
Lock ring of the internal hinge of a shaft of a drive of a wheel replace new at each removal.


Fig. 3.86. Anti-vibrating cargo on driving to a shaft


Check anti-vibrating cargo (fig. 3.86) on existence of cracks and wear.

PREVENTION
After each removal replace самоконтрящуюся a nut and шплинт new.

Installation
External diameter of a lock ring of the internal hinge of a shaft should be equal 27+0,4 mm.
Tighten carving connections by the moments specified below.

       NOTES
At carrying out repair work dismantling of the external hinge is not allowed.
In hinges of a shaft special greasing is put. It is not recommended to use greasing of other brands.
Collars of fastening of protective covers replace new at each removal.

Moments of an inhaling of carving connections, N · m
Nut of fastening of a finger of the spherical hinge of a tip of steering draft..... 24–34
Nuts of bolts of fastening of a rack of a suspension bracket to a rotary fist..... 110–130
Nut of a nave of a wheel..... 200–260

       NOTE
In case of a reuse of covers wrap up shlitsa of a shaft a sticky tape not to damage covers at removal.

Put transmission oil on a shlitsevy shaft of the internal hinge of a shaft of a drive of a wheel and a being interfaced surface of a case of a transmission.
At connection of a shaft of a drive of a wheel with a case of a transmission track to damaging a gryazeotrazhatelny ring.

Fig. 3.87. Lock ring of the internal hinge of a power shaft


Before connection of a shaft with a transmission establish on it a lock ring a cut down (fig. 3.87) .
After installation of a shaft be convinced that it does not move from effort of a hand.
Establish washers the concave party inside, tighten a nut of fastening of a nave and законтрите its shplinty.

PREVENTION
Reliably fix clips that at car operation collars did not weaken.

Dismantling and assembly of drives of forward wheels

Fig. 3.88. Drive of a forward wheel: 1–lock ring; 2–case of the internal hinge; 3–lock ring; 4–a holder of the internal hinge with rollers; 5–protective cover of the internal hinge; 6–external collar of fastening of a protective cover of the internal hinge; 7–internal collar of fastening of a protective cover of the internal hinge; 8–collar of fastening of anti-vibrating cargo; 9–anti-vibrating cargo; 10-internal collar of fastening of a protective cover of the external hinge; 11-external collar of fastening of a protective cover of the external hinge; 12-protective cover of the external hinge; 13-external hinge; 14-gear wreath of the wheel sensor of anti-blocking system of brakes (ABS); 15-gryazeotrazhatelny ring; 16-spring washer; 17-a nut of fastening of a drive in a nave of a forward wheel; 18-шплинт


The drive of a forward wheel is shown on fig. 3.88 .
Dismantling 
Remove collars of fastening of a cover of the internal hinge and shift a cover from the hinge case, thus track to damaging a cover.
Separate a cover from the internal hinge.

Fig. 3.89. Removal of a lock ring


Fig. 3.90. Installation site of anti-vibrating cargo


Remove a lock ring (fig. 3.90) and take out a holder with rollers from the hinge case.
Clear a working part.

Table 3.3 
The size A (for the left and right shaft), mm
Shaft
Cars with the engine in working volume 1,1; 1,3; 1,5; 1,6 l
mechanical transmission
automatic transmission
The left
-
185,4 +/-2
The right
390 +/-2
390 +/-2


PREVENTION
Reliably fix clips that at operation of the car did not weaken collars.

Fig. 3.91. Collars of fastening of anti-vibrating cargo


Screw-driver unbutton a clip of a collar and remove from a shaft covers of internal and external hinges.
By means of the adaptation 09495-33000 or other suitable adaptation remove a gryazeotrazhatelny ring from the case of the external hinge.

Fig. 3.92. The adjusting sizes at installation of a gryazeotrazhatelny ring and a gear wreath of the wheel ABS sensor


Assembly